The key to the much smaller design is the use of digitisers and AWGs by Spectrum Instrumentation that offer sub-nano second and coherence precision to generate the scanner-signals and capture the results
Neoscan Solutions has invented a smaller and lighter MRI scanner which could be placed directly in the children’s ward of a hospital to keep journeys short and to scan sick babies in their sleep. The key to the much smaller design is the use of digitisers and Arbitrary Waveform Generators (AWGs) by Spectrum Instrumentation that offer sub-nano second and coherence precision to generate the scanner-signals and capture the results.
Current MRI scanners weigh around eight tons and therefore need to be located on floors that can take this weight, which means either specially reinforced floors or locating them in a basement. They require ca. 40 square metres for the scanner, all the supporting equipment, and need to be supercooled with liquid helium, which needs special handling.
“Having worked with MRI scanners for many years, I recognised the problem. Scanning a sick child usually means a long journey out of the ward to the scanner and babies may need support equipment that is not easily transportable. Because of this, sometimes an MRI-scan is not even done. We have designed an MRI scanner specifically for new-borns and infants which means that the hole in the middle is only 30 cm in diameter, not 60 cm. As a result, the scanner is much smaller (170 cm x 150 cm x 110 cm) and can go through standard doorways. With a weight of only 2,000 kg, it can be located on standard floors, and needing only ten square metres, it can be installed in a spare room directly on the children’s ward. Carrying a sleeping baby only a few metres to the MRI is a big advantage, saving a long journey through the building and the need for sedatives to keep the baby motionless for the scan,” explained Stefan Roell, Founder, Neoscan Solutions in Germany.
“The technology and field strength of the Neoscan machine is identical to current scanners so that no new clinical studies are required to validate it. Achieving this needed several innovations by the company. Firstly, to shrink the size, the team had to develop a dry magnet that would create the standard 1.5 Tesla field inside the hole, but without requiring liquid helium. This is done by an inner, cylindrical magnet generating 2.5T and then an outer cylindrical magnet that counteracts the inner field to provide strong, active magnet shielding so that there is no stray magnetic field left beyond about one metre from the device’s cover,” he added.
The second innovation was in the control electronics. Current MRI scanners typically require three big racks of specially developed electronics that have been custom designed and built by the MRI manufacturer. Neoscan Solutions chose a different approach. The team uses a PC which runs the software that Neoscan has created plus high-end measurement PC-cards from Spectrum Instrumentation. The signals for the MRI are generated by the M4i.6620-x8 and M2p.6546-x4 AWGs and then analysed using an M2p.5968-x4 digitiser. The system uses Spectrum’s SCAPP software drivers that enable a graphics processor with 5,000 cores to perform the parallel processing, instead of using only eight or 16 cores of a normal CPU.
“As a start-up, we could not afford to create specialised hardware and so we used this route of high quality, standard cards providing a platform to run our software on. This meant that we could focus our skills on the software development with fast development cycles in the knowledge that the hardware was already tried and tested. This was only possible because of the design quality of the Spectrum cards. For MRI, it is vital that there is phase coherence in the 64MHz signals, otherwise there will be cancellation effects. In practice, that means that the AWG and matching digitiser have to have sub-nanosecond coherence precision, which the Spectrum cards achieve. During the research phase, it was hard to determine this from the specifications of the cards provided by the various suppliers that we contacted, as it is a rather unusual level of detail. However, Spectrum was outstanding in helping us with technical support both in the specification of the best cards to use and then again during the implementation. A rival proposal took weeks longer to arrive and was grossly over-specified and over-priced as they had not made the effort to understand the detail of our project.”
Neoscan will be shortly installing its first devices in German hospitals where it can be seen in operation by prospective customers as it takes images of babies. The certification process with a CE mark is expected to be completed before the end of 2021.
“This approach of a readily available hardware platform running specially-designed software worked well for us as it has enabled us to create a product much faster. I think it is an elegant solution that could be used for many other complex machines such as CT scanners and ultrasound machines, especially as it enables innovative new approaches to be easily tried and evaluated just through software changes,” Dr Roell concluded.
- Advertisement -